Caple Industrial Solutions
0
0
Currency

Lamello Tips and Tricks for Furniture Makers in India

Lamello expertise · Caple, authorised India distributor

Lamello tips and tricks: faster, cleaner furniture joinery

Nine practical Lamello techniques for furniture factories, interior fit-out contractors and carpenters in India, each with step-by-step photos. Each one removes a clamp, a screw, a site helper or a rework step. Caple demonstrates every tip at its Centre of Excellence in Pelhar, Maharashtra.

Cabinet carcass glued with Lamello Tenso P connectors and no clamps

1. Glue carcasses without clamps: Tenso P

Tenso P is a self-clamping connector. It pulls mitre and butt joints tight while the glue sets, at any angle, so the part can move to the next station straight away.

  • You get: tight, concealed glued joints at any angle
  • You save: clamps, tape and clamping time (Lamello cites about 40 seconds per connector)
  • You achieve: faster flow through assembly
  1. Cut all components and mill the P-System grooves (Zeta P2 or CNC).
  2. Slide the connector halves into the grooves.
  3. Apply glue.
  4. Press on the preload clip so the parts close easily.
  5. Assemble the components.
  6. Done: a glued carcass with no waiting, clamps or tape.
Step-by-step photos (6)
Tenso P step 1: Cut all components and mill the P-System grooves (Zeta P2 or CNC)
Step 1
Tenso P step 2: Slide the connector halves into the grooves
Step 2
Tenso P step 3: Apply glue
Step 3
Tenso P step 4: Press on the preload clip so the parts close easily
Step 4
Tenso P step 5: Assemble the components
Step 5
Tenso P step 6: Done: a glued carcass with no waiting, clamps or tape
Step 6
Thin HPL false front fixed to a drawer with Lamello Tenso P-10

2. Fix thin HPL or CDF fronts: Tenso P-10

Thin fronts look light and modern but are hard to fix without screws showing. Tenso P-10 joins thin false fronts and drawer facings invisibly.

  • You get: no screw heads or holes on the visible face
  • You save: filling and touch-up work
  • You achieve: premium thin-front designs with a repeatable method
  1. Set the angle stop to half the material thickness.
  2. Groove the edge of the drawer side at depth setting 12.
  3. Fit the 4 mm P-System depth adjuster cap (effective depth 8 mm).
  4. Add the planned overhang of the front to the half-thickness setting and lock it.
  5. Groove the face of the front. A second angle stop improves stability.
  6. Slide the Tenso P-10 halves without springs into the face grooves.
  7. Slide the halves with springs into the 12 mm edge grooves.
  8. Use the push-in tool to fit the preload clip onto the spring half.
  9. Apply glue and press the joint together.
Step-by-step photos (9)
Tenso P-10 step 1: Set the angle stop to half the material thickness
Step 1
Tenso P-10 step 2: Groove the edge of the drawer side at depth setting 12
Step 2
Tenso P-10 step 3: Fit the 4 mm P-System depth adjuster cap (effective depth 8 mm)
Step 3
Tenso P-10 step 4: Add the planned overhang of the front to the half-thickness setting and lock it
Step 4
Tenso P-10 step 5: Groove the face of the front. A second angle stop improves stability
Step 5
Tenso P-10 step 6: Slide the Tenso P-10 halves without springs into the face grooves
Step 6
Tenso P-10 step 7: Slide the halves with springs into the 12 mm edge grooves
Step 7
Tenso P-10 step 8: Use the push-in tool to fit the preload clip onto the spring half
Step 8
Tenso P-10 step 9: Apply glue and press the joint together
Step 9
One installer assembling a large wardrobe with Lamello Cabineo connectors

3. Assemble large wardrobes alone: Cabineo

Made-to-measure wardrobes often have to go into flats as loose panels. With Cabineo fitted in the factory, one installer can assemble the carcass on site.

  • You get: self-locating panels and consistent joint tension
  • You save: a second installer on many jobs, plus site time
  • You achieve: flat-pack delivery with lower freight volume
  1. Deliver the panels flat-packed with Cabineo already fitted.
  2. Stand the side on the plinth. The projecting screw locates it.
  3. Join the parts with a cordless driver and the Cabineo bit.
  4. Work fast with the torque preset to about 2.5 Nm.
  5. Position the top and push it against the side.
  6. Screw the front corner tight. One person can do this alone.
  7. Slide in the fixed shelves with the Cabineo screw backed off, then fix them in position.
  8. Tip: insert a shelf support and fit the Cabineo on the opposite side.
  9. Add Cabineo cover caps if required.
Step-by-step photos (9)
Cabineo step 1: Deliver the panels flat-packed with Cabineo already fitted
Step 1
Cabineo step 2: Stand the side on the plinth. The projecting screw locates it
Step 2
Cabineo step 3: Join the parts with a cordless driver and the Cabineo bit
Step 3
Cabineo step 4: Work fast with the torque preset to about 2.5 Nm
Step 4
Cabineo step 5: Position the top and push it against the side
Step 5
Cabineo step 6: Screw the front corner tight. One person can do this alone
Step 6
Cabineo step 7: Slide in the fixed shelves with the Cabineo screw backed off, then fix them in position
Step 7
Cabineo step 8: Tip: insert a shelf support and fit the Cabineo on the opposite side
Step 8
Cabineo step 9: Add Cabineo cover caps if required
Step 9
Wood panel joined to an aluminium profile with Cabineo 8 M6 and a blind rivet nut

4. Join panels to aluminium profiles: Cabineo 8 M6

Retail fixtures, kitchens and exhibition stands increasingly combine wood panels with aluminium frames. A pressed-in M6 blind rivet nut gives the Cabineo 8 M6 screw a secure thread in the profile.

  • You get: the full clamping force of Cabineo in mixed-material furniture
  • You save: special brackets and visible fixings
  • You achieve: detachable wood-and-metal designs
  1. Mill or drill the Cabineo 8 M6 pocket on the CNC machine.
  2. Fit the Cabineo 8 M6 and tap it into place.
  3. Drill the aluminium profile to the rivet-nut maker's size.
  4. Select an M6 blind rivet nut and load the rivet-nut pliers.
  5. Press in the rivet nut. Use a countersunk head for a flush finish.
  6. Align the panel on the rivet nut and screw it tight.
Step-by-step photos (6)
Cabineo 8 M6 step 1: Mill or drill the Cabineo 8 M6 pocket on the CNC machine
Step 1
Cabineo 8 M6 step 2: Fit the Cabineo 8 M6 and tap it into place
Step 2
Cabineo 8 M6 step 3: Drill the aluminium profile to the rivet-nut maker's size
Step 3
Cabineo 8 M6 step 4: Select an M6 blind rivet nut and load the rivet-nut pliers
Step 4
Cabineo 8 M6 step 5: Press in the rivet nut. Use a countersunk head for a flush finish
Step 5
Cabineo 8 M6 step 6: Align the panel on the rivet nut and screw it tight
Step 6
Sloping shoe rack shelf secured against lifting with Lamello Cabineo X

5. Secure sloping shelves: Cabineo X

Shoe racks and wine racks need shelves that stay adjustable but cannot slide or be lifted out. The open housing of Cabineo X does this without an extra row of holes in front of the shelf lip.

  • You get: adjustable shelves that are locked against lifting
  • You save: an extra line-boring row
  • You achieve: cleaner sides and fewer customer complaints
  1. Download the CAD data from the Lamello website.
  2. Mill or drill the connector pocket on the CNC machine.
  3. Position the connector and press it in.
  4. For tool-free adjustment, insert shelf supports into the holes.
  5. For load-bearing shelves, use a Cabineo screw instead.
  6. With shelf supports, press the shelf down onto them from above.
  7. With screws, lay the shelf in place and tighten the pre-fitted screws.
  8. Add cover caps if required.
  9. The sloping shelf is now secured against slipping or lifting.
Step-by-step photos (9)
Cabineo X step 1: Download the CAD data from the Lamello website
Step 1
Cabineo X step 2: Mill or drill the connector pocket on the CNC machine
Step 2
Cabineo X step 3: Position the connector and press it in
Step 3
Cabineo X step 4: For tool-free adjustment, insert shelf supports into the holes
Step 4
Cabineo X step 5: For load-bearing shelves, use a Cabineo screw instead
Step 5
Cabineo X step 6: With shelf supports, press the shelf down onto them from above
Step 6
Cabineo X step 7: With screws, lay the shelf in place and tighten the pre-fitted screws
Step 7
Cabineo X step 8: Add cover caps if required
Step 8
Cabineo X step 9: The sloping shelf is now secured against slipping or lifting
Step 9
Scribe strip fitted to an uneven wall using Lamello K20 adhesive biscuits

6. Fit scribe strips without tape: K20 biscuits

Fitting scribe strips is often the last job on site. The side ribs of the K20 biscuit hold the strip in place while the adhesive cures.

  • You get: a tight fit to uneven walls
  • You save: tape, clamps and refinishing
  • You achieve: a faster, cleaner handover
  1. Mark groove positions on the mounting strip and scribe strip, no more than 300 mm apart.
  2. Set the Classic X front stop to 90° and depth to 20. Groove the edge of the mounting strip.
  3. Cut two rows of grooves 20 mm apart in the face of the scribe strip, using two stop squares.
  4. Fix the mounting strip to the carcass, projecting 2 mm, and screw it on.
  5. Fit biscuits in the mounting strip and push the scribe strip onto the second row.
  6. Transfer the wall contour with a scribing gauge set to the 20 mm row spacing.
  7. Cut and plane to the line, then sand the edges.
  8. Apply adhesive and insert the K20 biscuits.
  9. Fit the scribe strip. No rework needed.
Step-by-step photos (9)
K20 biscuits step 1: Mark groove positions on the mounting strip and scribe strip, no more than 300 mm apart
Step 1
K20 biscuits step 2: Set the Classic X front stop to 90° and depth to 20. Groove the edge of the mounting strip
Step 2
K20 biscuits step 3: Cut two rows of grooves 20 mm apart in the face of the scribe strip, using two stop squares
Step 3
K20 biscuits step 4: Fix the mounting strip to the carcass, projecting 2 mm, and screw it on
Step 4
K20 biscuits step 5: Fit biscuits in the mounting strip and push the scribe strip onto the second row
Step 5
K20 biscuits step 6: Transfer the wall contour with a scribing gauge set to the 20 mm row spacing
Step 6
K20 biscuits step 7: Cut and plane to the line, then sand the edges
Step 7
K20 biscuits step 8: Apply adhesive and insert the K20 biscuits
Step 8
K20 biscuits step 9: Fit the scribe strip. No rework needed
Step 9
Mitred furniture parts joined with detachable Lamello Clamex S-20 connectors

7. Detachable joints at any angle: Clamex S-20

Clamex S-20 brings detachable Clamex joints to a classic biscuit joiner with a 4 mm cutter. It suits mitres from 22.5° to 180° and materials from 8 mm thick.

  • You get: detachable mitre and angle joints without a P-System machine
  • You save: buying a dedicated joiner for occasional knock-down work
  • You achieve: furniture that can be taken apart and moved as often as needed
  1. Cut 4 mm grooves into the edge.
  2. Transfer the centre mark onto the first workpiece.
  3. Hold the workpieces together and transfer the centre position.
  4. Align the machine and set the stop square on the front edge for an exact cut.
  5. Drill a 6 mm access hole in the face with the drilling and alignment jig.
  6. Fit the connector on the jig, slide it into the groove and align it with light hammer taps.
  7. Fix the connector halves with the screws. Pre-drill 2 mm in brittle materials.
  8. Assemble and align both parts.
  9. Tighten the Clamex S-20. The parts can be taken apart and rejoined as often as needed.
Step-by-step photos (9)
Clamex S-20 step 1: Cut 4 mm grooves into the edge
Step 1
Clamex S-20 step 2: Transfer the centre mark onto the first workpiece
Step 2
Clamex S-20 step 3: Hold the workpieces together and transfer the centre position
Step 3
Clamex S-20 step 4: Align the machine and set the stop square on the front edge for an exact cut
Step 4
Clamex S-20 step 5: Drill a 6 mm access hole in the face with the drilling and alignment jig
Step 5
Clamex S-20 step 6: Fit the connector on the jig, slide it into the groove and align it with light hammer taps
Step 6
Clamex S-20 step 7: Fix the connector halves with the screws. Pre-drill 2 mm in brittle materials
Step 7
Clamex S-20 step 8: Assemble and align both parts
Step 8
Clamex S-20 step 9: Tighten the Clamex S-20. The parts can be taken apart and rejoined as often as needed
Step 9
Thin 8 mm shelf joined detachably with Lamello Clamex S-20

8. Detachable joints in 8 mm panels: Clamex S-20

Thin panels are now common in furniture design. With its 4 mm groove, Clamex S-20 makes detachable joints in materials from 8 mm thick using any standard biscuit joiner.

  • You get: knock-down joints in slim, modern designs
  • You save: bulky fittings that do not suit thin panels
  • You achieve: lighter furniture that still ships flat
  1. Set the stop square to half the material thickness.
  2. Set depth 20 and groove the edge of the 8 mm shelf.
  3. Drill a 6 mm access hole in the shelf with the drilling and alignment jig.
  4. Align the machine and groove the face of the side panel.
  5. Fit the connector on the jig and slide it into the groove.
  6. Tap the connector lightly until it is parallel to the face.
  7. Fix the halves with the screws supplied. Pre-drill 2 mm in brittle materials.
  8. Assemble the parts and tighten with the Allen key.
Step-by-step photos (8)
Clamex S-20 step 1: Set the stop square to half the material thickness
Step 1
Clamex S-20 step 2: Set depth 20 and groove the edge of the 8 mm shelf
Step 2
Clamex S-20 step 3: Drill a 6 mm access hole in the shelf with the drilling and alignment jig
Step 3
Clamex S-20 step 4: Align the machine and groove the face of the side panel
Step 4
Clamex S-20 step 5: Fit the connector on the jig and slide it into the groove
Step 5
Clamex S-20 step 6: Tap the connector lightly until it is parallel to the face
Step 6
Clamex S-20 step 7: Fix the halves with the screws supplied. Pre-drill 2 mm in brittle materials
Step 7
Clamex S-20 step 8: Assemble the parts and tighten with the Allen key
Step 8
Lightweight honeycomb panel joined with a glued Lamello LC P-16 connector

9. Stronger lightweight panels: glue the LC P-16

Large, lightweight honeycomb panels save weight but need strong joints. For heavily loaded parts, the LC P-16 can be glued through its built-in glue channels.

  • You get: strong joints in lightweight board
  • You save: weight and material on large panels
  • You achieve: big doors, tops and partitions that are easier to handle and install
  1. Use the LC P-16 configurator to find the height setting and connector. Groove at depth P-18 with the 2 mm adjuster cap (16 mm deep).
  2. Drill a 6 mm access hole with the drilling jig.
  3. Fit the positioning clip for exact side alignment and continue machining.
  4. Groove the face at depth P-10 without the adjuster cap. A second angle stop improves stability.
  5. Insert lever-free connector halves, such as Clamex P-10, into the face. Clamex P-14 also suits skins over 4 mm.
  6. Slide in the LC P-16 from the front. For LC P-16 × 11, glue the side grooves first.
  7. For LC P-16 × 17 and × 22, inject glue through the glue channels.
  8. Insert Clamex P-14 halves with lever (or Clamex CNC or Flexus).
  9. Assemble and tighten with the assembly tool. Add a cover cap if required.
Step-by-step photos (9)
glue the LC P-16 step 1: Use the LC P-16 configurator to find the height setting and connector. Groove at depth P-18 with the 2 mm adjuster cap (16 mm deep)
Step 1
glue the LC P-16 step 2: Drill a 6 mm access hole with the drilling jig
Step 2
glue the LC P-16 step 3: Fit the positioning clip for exact side alignment and continue machining
Step 3
glue the LC P-16 step 4: Groove the face at depth P-10 without the adjuster cap. A second angle stop improves stability
Step 4
glue the LC P-16 step 5: Insert lever-free connector halves, such as Clamex P-10, into the face. Clamex P-14 also suits skins over 4 mm
Step 5
glue the LC P-16 step 6: Slide in the LC P-16 from the front. For LC P-16 × 11, glue the side grooves first
Step 6
glue the LC P-16 step 7: For LC P-16 × 17 and × 22, inject glue through the glue channels
Step 7
glue the LC P-16 step 8: Insert Clamex P-14 halves with lever (or Clamex CNC or Flexus)
Step 8
glue the LC P-16 step 9: Assemble and tighten with the assembly tool. Add a cover cap if required
Step 9

See these tips live, or get a Lamello quote

Tell us what you make and the panel material and thickness. Caple will suggest the connector, machine and cutter, and show it at our Pelhar Centre of Excellence.

Lamello tips: frequently asked questions

Which machine do I need for these tips?

Tenso P, Tenso P-10 and LC P-16 (tips 1, 2 and 9) need the P-System groove from a Zeta P2 or a suitably equipped CNC machine. Cabineo tips (3 to 5) are machined on a CNC. K20 and Clamex S-20 (tips 6 to 8) work with a classic biscuit joiner with a 4 mm cutter, such as the Classic X.

Can I buy Tenso, Cabineo, Clamex and K20 in India?

Yes, from Caple Industrial Solutions, Lamello's authorised India distributor. Some items, such as K20, Cabineo X and LC P-16, are supplied on request; WhatsApp us for stock and lead time.

Will these tips reduce my cost?

They remove specific steps, such as clamping or a second installer. Actual savings depend on your process, so compare the total cost per installed product; Caple can do this with you on a real job.

Techniques and step photos adapted from Lamello Tips and Tricks. Images © Lamello AG. Lamello, Zeta, Tenso, Cabineo, Clamex and Classic X are trademarks of Lamello AG.

Items have been added to cart.
One or more items could not be added to cart due to certain restrictions.
Added to cart
Quantity updated
- An error occurred. Please try again later.
Deleted from cart
- An error occurred. Please try again later.
Chat on WhatsApp