John Guest Pneumatic Air Piping

The Easy to Use Push Fit System For Compressed Air

The fittings are produced in either a tough
engineering plastics material or in brass in
sizes 12mm to 28mm. They are intended
for use with John Guest nylon pipe but
can also be used with copper or
aluminium pipe.

• Installation time reduced by at least 50%
• Safe, secure, leakproof
• Easy to alter or extend a system
• Lightweight and easy to handle
• No corrosion, reduced maintenance

Easy to Make a Connection

The John Guest Push in
Fitting has a collet (gripper) with
stainless steel teeth which hold the
pipe firmly in position and an ‘O’ ring to
provide a permanent leak proof seal.

Stem Elbow

Designed to simplify pipe connections in restricted spaces,
the Stem Elbow gives an instant swivel fitting so a pipe can
be orientated in any direction.

Can be used with an
elbow to make
‘U’ turn connection.
Please note a collet cover cannot
be used on a Speedfit end assembled
with the stem of a 22mm Stem Elbow.

Can be used
with a Tee.

Aluminium Pipe

3 metre straight lengths.
15 to 22mm in packs of 20
3m lengths.
28mm in packs of 10
3m lengths.

PART NO – SIZE MM X M
AL-RM1513-3M-20B  – 15 x 3
AL-RM1816-3M-20B  – 18 x 3
AL-RM2220-3M-20B  – 22 x 3
AL-RM2826-3M-10B  – 28 x 3

Water Tap Tee Converter

The Water Trap Tee Convertor is a simple convenient way of
converting a standard John Guest 28mm Tee to a Water Trap Tee.
This will stop condensing water entering the vertical take
off spur.
The air supply needs to be installed with the correct fall and
water drain points regularly vented.

To Assemble

Use either John Guest 28mm Nylon Pipe or 28mm copper pipe.
The pipe to be cut square and be free of burrs.
Press the shorter spigot into the pipe. The fit on copper pipe will
be loose, this will not affect the function.
Push the pipe and convertor up to the pipe stop of the centre leg
of the tee.
Turn the screw cap approx 1/4 turn to lock the pipe in position.

End Stop

The End Stop can be used to provide a permanent connection or
a temporary shut off. Because it is easy to disconnect the fitting
from the pipe, the End Stop can be put in place to be removed at
a later date to allow a system to be extended or modified.

Equal Tee

PART NO. – PIPE OD
PM0212E  – 12
PM0215E  – 15
PM0218E  – 18
PM0222E  – 22
PM0228E  – 28

Straight Adaptor

PART NO.- PIPE THREAD – OD BSP
PM011213E  – 12  –  3/8
PM011214E  – 12 –  1/2
PM011514E  – 15  – 1/2
PM011516E  – 15  – 3/4
PM011814E  – 18  –  1/2
PM012216E  – 22 –  3/4

Reducing Tee

PART NO.  – PIPE OD ENDS – TUBE OD  BRANCH
PM3018AE  –  18  – 15
PM3022AE –  22  – 15

Equal Elbow

PART NO. –  PIPE OD
PM0312E  –  12
PM0315E  –  15
PM0318E  –  18
PM0322E  –  22
PM0328E  –  28

Straight Connector

PART NO.  – PIPE OD
PM0412E  –  12
PM0415E  –  15
PM0418E  –  18
PM0422E  –  22
PM0428E  –  28

Reducer

PART NO.  – STEM PIPE – OD OD
PM061512E  – 15 – 12
PM061815E  – 18 – 15
PM062215E  – 22 – 15
PM062218E  – 22 – 18
PM062815E  – 28 – 15
PM062822E  – 28 – 22

U-Bend

PART NO.  – SIZE
PMUB15E  –  15

Plug

John Guest is the leader in Europe for Speed fit fittings. The John Guest range of push-in fittings and aluminum pipes provide the ideal connection from compressor receiver to air line service components through to complete ring main and drop downs and take off points. There is no need to prepare threaded pipes or use solvents, all the connections can be made with a simple push-in action which is modular. The system is then immediately ready for use and lasts for a lifetime. Complex systems can be assembled much more rapidly than with traditional methods and because fittings are easy to disconnect, and alter or extend with much reduced production down time. The John Guest fittings are produced in either a tough engineering plastics material or in brass in sizes 12mm to 28mm. They are intended for use with John Guest nylon pipe but can also be used with copper or aluminum pipe.Caple is Dealer for John Guest Pneumatic Piping Pipes, in Mumbai and has successfully taken up many trunkey projects.

RELATED PRODUCTS